Academy » Costs and Productivity
Costs and Productivity — Lesson 1: OEE in Practice: What This Number Really Says About Your Line
Costs and Productivity · 3 min read · 15.11.2026

Three Multiplications That Reveal the Truth
OEE (Overall Equipment Effectiveness) is the product of three factors: availability, performance and quality. OEE = availability × performance × quality. There is nothing more to it.
Availability is the share of time the machine actually runs out of the time it was supposed to run. Performance compares actual units produced with the theoretical maximum. Quality counts how many units passed without rework or scrap.
It sounds simple. The problem lies in the data. Most companies calculate OEE from planned figures, not actual ones — and the result then looks better than how the line really runs.
Look at how the multiplication works. Availability 90%, performance 90%, quality 95%. On paper, a good line. The resulting OEE? 77%. Almost a quarter of capacity is gone.
A 65% OEE doesn't mean the line is bad. It means you've identified 35% of capacity that you're not using yet — and that's extra capacity for free.

Where OEE Goes Wrong Most Often
In projects at manufacturing companies, we keep seeing three recurring mistakes:
- Planned downtime isn't accounted for correctly. A machine setup takes 30 minutes, someone declares it "planned" — and availability gets artificially inflated. Setup is a cost, even when it's scheduled.
- The theoretical cycle time comes from a catalog, not from the line. The manufacturer states 12 seconds per unit, while your line actually runs at 15. A 100% performance then means something completely different from what you think.
- Quality is only measured at the end. As long as every defective unit gets reworked in the next operation and no scrap is produced, it never makes it into OEE. Hidden rework disappears from the curve.
A concrete example from our practice: a line with a measured OEE of 84%. After recalculating with real setup times and in-process rework, it came out at 71%. The 13-percentage-point difference represented roughly 90 hours per month — lost before anyone even started optimizing the line.
How to Interpret the Number You Get
OEE by itself doesn't improve anything. Improvement comes from breaking it down into the three factors — each has a different problem owner:
- Low availability = downtime, breakdowns, setup. These are addressed by maintenance and planning. The industry standard for the breakdown component is MTBF — mean time between failures.
- Low performance = micro-stops, short stoppages, slow pace. This is addressed by lean and the work of supervisors directly at the line.
- Low quality = process parameters, material or skills. This is addressed by the quality engineer together with the process engineer.
An 80% OEE with 95% availability is a completely different story than 80% with 95% quality. The first says "nobody may slow down," the second "something is wrong with the process." Until you know the breakdown, you're throwing money at the wrong solution.
This Week's Exercise
Pick one line or one key machine. During one shift, measure manually:
- The actual machine running time — the start and end of every stoppage, including those under 5 minutes.
- The number of units produced and, of those, the number of good units.
- The theoretical cycle time per unit based on the actual pace of the line, not the catalog.
From these three numbers, calculate the OEE and break it down into the three factors. Most teams need just one shift to discover 2–3 micro-stops nobody knew about until now. Typically, you'll find 20–40 minutes lost in chunks of 2–3 minutes. That's half an hour of capacity every day.
Key Takeaways
- OEE is the product of availability, performance and quality — three decent percentages turn into an average result through multiplication.
- Measure from real data: setup, in-process rework and the real cycle time are the most common sources of distortion.
- The number alone says nothing — only the breakdown into three factors shows who needs to address what.
- Manual measurement over one shift will reveal micro-stops that don't appear in the system.
If you want to measure OEE and other productivity indicators systematically across multiple lines, check out our e-learning offer, where you'll find an entire series on costs and productivity.
Next time, we'll look at the biggest eater of availability — downtime. We'll calculate what an hour of a stopped machine really costs, and show you how to compute that number precisely.